Cement-based finishing coat for concrete walls and ceilings and cement-sand rendered surfaces.

Planitop S12 is a cement-based water-resistant mortar specially formulated as a finishing coat for both interior and exterior use.

TECHNICAL DATA:
Storage: 12 months.
Consumption: 1.3 kg/m2 for each mm thickness.
Packaging: 20 kg bags.

Eco Prim Grip is a multi-purpose, ready-to-use primer for internal and external floors and walls and may be used to improve the bond of all types of cement, gypsum and lime-based plasters on substrates made from concrete, brickwork, vibro-compressed concrete blocks, lightweight blocks and gypsum.
Technical data:
Waiting time before applying render: 15-20 minutes (please consult data sheet).
Waiting time before applying smoothing compound: 30 minutes (please consult data sheet).
Colour: Grey.
Storage: 24 months in its original packaging.

MAPEI EPOJET LV (4KG) Two-Component Epoxy Resin, with very Low Viscosity for injection in microcracks

WHERE TO USE

• Monolithic sealing of cracks.

• Bonding steel plates to concrete (béton plaqué) by low pressure injection.

Some application examples

• Structural repair of beams, pillars and cracked floors by low pressure injection.

• Reinforcement of beams and floors by injection with the béton plaqué method, when the plates to be bonded are fitted with lateral flaps and it is therefore impossible to apply Adesilex PG1 or Adesilex PG2.

• Repair of architectural concrete, wall coverings and architectural elements that are crumbly.

• Structural consolidation and restoration of civil and industrial road constructions and underground works that show signs of microcracking.

• Sealing of cracks in cementitious screeds.

• Restoration, by injection, of concrete structures damaged by earthquakes, settlements or impacts.

TECHNICAL CHARACTERISTICS

Epojet LV is a two-component epoxy adhesive. The pre-measured components (component A = resin and component B = hardener) must be mixed together before being used.

Once mixed, Epojet LV becomes a very fluid liquid that can easily penetrate even in microcracks.

Epojet LV polymerizes without shrinkage and once hardened is waterproof and resists chemical agents present in the atmosphere. Epojet LV has very good insulating properties and high mechanical strength.

Description
Idrostop PVC is a highly flexible waterstop made from high-quality thermo-plastic vinyl resins, forming a product with good resistance to mechanical stresses, aggressive chemical action in alkaline environment, sea-water and acids. Idrostop PVC is used within concrete structures exposed to temperatures from -30°C to +70°C and is highly resistant to damage caused by sunlight, ozone and other aggressive agents present in the atmosphere and water table. The dimensions and type of Idrostop PVC used for each application generally depends on the following parameters:
- type of structure
- amount and type of movements predicted (e.g. no movement, axial movement, a combination of axial and transversal movements, etc.);
- thickness of the cast concrete
- Technical Data Sheet (T.D.S)

Sizes Available
Idrostop PVC CJ is available in three sizes:
CJ15 (width 15 cm)
CJ20 (width 20 cm)
CJ25 (width 25 cm)

Idrostop PVC EJ is available in three sizes:
EJ15 (width 15 cm)
EJ20 (width 20 cm)
EJ25 (width 25 cm)

Idrostop PVC RGC is available in two sizes:
RGC20 (width 20 cm)
RGC25 (width 25 cm)

Idrostop PVC RGE is available in two sizes:
RGE20 (width 20 cm)
RGE25 (width 25 cm)

Description
Idrostop PVC is a highly flexible waterstop made from high-quality thermo-plastic vinyl resins, forming a product with good resistance to mechanical stresses, aggressive chemical action in alkaline environment, sea-water and acids. Idrostop PVC is used within concrete structures exposed to temperatures from -30°C to +70°C and is highly resistant to damage caused by sunlight, ozone and other aggressive agents present in the atmosphere and water table. The dimensions and type of Idrostop PVC used for each application generally depends on the following parameters:
- type of structure
- amount and type of movements predicted (e.g. no movement, axial movement, a combination of axial and transversal movements, etc.);
- thickness of the cast concrete
- Technical Data Sheet (T.D.S)

Sizes Available
Idrostop PVC CJ is available in three sizes:
CJ15 (width 15 cm)
CJ20 (width 20 cm)
CJ25 (width 25 cm)

Idrostop PVC EJ is available in three sizes:
EJ15 (width 15 cm)
EJ20 (width 20 cm)
EJ25 (width 25 cm)

Idrostop PVC RGC is available in two sizes:
RGC20 (width 20 cm)
RGC25 (width 25 cm)

Idrostop PVC RGE is available in two sizes:
RGE20 (width 20 cm)
RGE25 (width 25 cm)

Description
Idrostop PVC is a highly flexible waterstop made from high-quality thermo-plastic vinyl resins, forming a product with good resistance to mechanical stresses, aggressive chemical action in alkaline environment, sea-water and acids. Idrostop PVC is used within concrete structures exposed to temperatures from -30°C to +70°C and is highly resistant to damage caused by sunlight, ozone and other aggressive agents present in the atmosphere and water table. The dimensions and type of Idrostop PVC used for each application generally depends on the following parameters:
- type of structure
- amount and type of movements predicted (e.g. no movement, axial movement, a combination of axial and transversal movements, etc.);
- thickness of the cast concrete
- Technical Data Sheet (T.D.S)

Sizes Available
Idrostop PVC CJ is available in three sizes:
CJ15 (width 15 cm)
CJ20 (width 20 cm)
CJ25 (width 25 cm)

Idrostop PVC EJ is available in three sizes:
EJ15 (width 15 cm)
EJ20 (width 20 cm)
EJ25 (width 25 cm)

Idrostop PVC RGC is available in two sizes:
RGC20 (width 20 cm)
RGC25 (width 25 cm)

Idrostop PVC RGE is available in two sizes:
RGE20 (width 20 cm)
RGE25 (width 25 cm)

DESCRIPTION:

High performance cementitious grout, polymer modified, for joints up to 6 mm.

APPLICATIONS:

Easy to apply and finish, smooth and compact, interior and exterior, floor and wall grouting of all types of ceramic tiles (double-fired, single-fired, klinker, porcelain tiles, etc.), terracotta, stone material (natural stone, marble ,granite, agglomerates, etc.), glass and marble mosaics.
Keracolor FF mixed with Fugolastic improves its final characteristics, reaching suitable strength even under particularly difficult conditions such as grouting facades, swimming pools, bathrooms, floors with heavy traffic.

TECHNICAL DATA

Pot life: approx. 2 hours.
Waiting time before finishing: 10-20 minutes.
Set to light foot traffic: 24 hours.
Ready for use: 7 days.
Application: MAPEI rubber trowel.
Finishing: Mapei sponge or Scotch-Brite® pad.
Consumption:  depends on the width of the joint, the size and thickness of the tiles.
 

Application: rubber MAPEI trowel or rake.
Finishing: MAPEI sponge or Scotch-Brite_® pad.
EMICODE: EC1 R Plus - very low emission.
Storage: 12 months (25 kg bags), 24 months (5 kg bags).
Consumption: according to the size of the joints.

Fine graded, water repellent grout for joints of up to 6mm. Made by the world’s largest manufacturer of adhesives, grouts, sealants and specialty products for the building industry.

• Cement Grey (113) colour

• Water-repellent

• Joint size up to 6mm

• Ready for use after 24 hours

• Colour-matched silicone available

Application: rubber MAPEI trowel or rake.
Finishing: MAPEI sponge or Scotch-Brite_® pad.
EMICODE: EC1 R Plus - very low emission.
Storage: 12 months (25 kg bags), 24 months (5 kg bags).
Consumption: according to the size of the joints.

TECHNICAL DATA

Pot life: approx. 2 hours.
Waiting time before finishing: 10-20 minutes.
Set to light foot traffic: 24 hours.
Ready for use: 7 days.
Colours: 11  (100,103,110,111,112,113,114,120,130,132,170)
Application: MAPEI rubber trowel.
Finishing: Mapei sponge or Scotch-Brite® pad.
Storage: 12 months (20 kg bag), 24 months (2 kg and 5 kg Alupak bags)
Consumption:  depends on the width of the joint, the size and thickness of the tiles.
Packaging:   2 kg, 5 kg and 20 kg bags

Fine-grained, high-performance white cementitious mortar for grouting joints up to 4 mm wide.
TECHNICAL DATA:
Pot life of mix: approx. 2 hours.
Waiting time before finishing: 10-20 minutes.
Set to light foot traffic: approx. 24 hours.
Ready for use: 7 days.
Colour: white.
Application: rubber MAPEI trowel or rake.
Finishing: MAPEI sponge or Scotch-Brite® pad.
EMICODE: EC1 R Plus - very low emission.
Storage: 12 months (22 kg bags), 24 months (5 kg bags).
Consumption: according to the size of the joints.

Fine-grained, high-performance white cementitious mortar for grouting joints up to 4 mm wide.

TECHNICAL DATA:

Pot life of mix: approx. 2 hours.

Waiting time before finishing: 10-20 minutes.

Set to light foot traffic: approx. 24 hours.

Ready for use: 7 days.

Colour: white.

Application: rubber MAPEI trowel or rake.

Finishing: MAPEI sponge or Scotch-Brite® pad.

EMICODE: EC1 R Plus - very low emission.

Consumption: according to the size of the joints.